本文发表在 rolia.net 枫下论坛1: Did the wash machine stop completely, timer also stopped? (This is would be an 110V power interruption)
2: Did you observe this? Is “Only” the pump is not pumping water out on the drain cycle, but the timer was running till the end of the wash cycle? If the answer is YES, the problems would be either the pump control electrical circuit, or the pump impeller mechanical problem.
On electrical problem,
2a: If you can’t hear the sound of pump motor is running. Check the pump motor wire connection, pump control engagement solenoid, and the pump control contact on the timer.
On mechanical problem,
2b: If you hear the motor is running, but not pumping water, check the pump impeller.
2c: If the water pump was run by the main motor same as the agitation, then check the pump engagement solenoid, this solenoid applies pressure from the main motor shift to the pump then it will move water.
Read the following"
The water pump recirculates water during the wash cycle and pumps it out for the spin cycle. Some washers use the recirculation to mix and distribute add-ins like bleach or fabric softener. In some models the spin cycle starts while the water is still in the tub; others drain first before the spin cycle starts.
A blocked or malfunctioning water pump can be responsible for many different washer problems; see our diagnostic page for the list. Note that while a problem may seem to be related to the pump, the problem may really lie in one of the connecting hoses. Each of the hoses that connects to the water pump should also be inspected. A blockage may occur anywhere in the water's pathway.
There are two types of pumps; direct drive and belt drive. The direct drive is mounted directly to the motor, the belt drive is mounted to the chassis. The direct drive style can be opened for complete inspection while belt drive models may or may not be designed to be opened. You can however, still remove the hoses and inspect the ports for a blockage. Inspecting the pump is fairly easy to do, but you will most likely have to open the washer's cabinet.
Typically one of three problems occur with the pump. The first is a blockage in the pump, often from small items like a sock. The second possibility is that the impeller blades become broken or worn down and cannot move water efficiently. Finally, in belt drive models, if the belt is loose or broken it does not turn the pump.
Locate the pump, it will have two, three or four hoses. Label each hose and where it connects. The hoses should each have a wire clamp or a hose clamp with a screw. Pinch the wire tabs together with pliers and wiggle the clamp farther up the hose. Screw style hose clamps are simply loosened by turning the screw, then slide the clamp up the hose. Now remove the hose from the port.
Direct drive pumps have metal clips that hold the cover plate unto the pump assembly. Use a screwdriver to pry up the clips and remove the cover. Pull off the pump's impeller unit and inspect for damage.
Belt drive pumps vary and may or may not be designed to open for repair. Examine the pump to determine whether it can be opened. If it cannot be opened the look into the ports for any blockage.更多精彩文章及讨论，请光临枫下论坛 rolia.net
2: Did you observe this? Is “Only” the pump is not pumping water out on the drain cycle, but the timer was running till the end of the wash cycle? If the answer is YES, the problems would be either the pump control electrical circuit, or the pump impeller mechanical problem.
On electrical problem,
2a: If you can’t hear the sound of pump motor is running. Check the pump motor wire connection, pump control engagement solenoid, and the pump control contact on the timer.
On mechanical problem,
2b: If you hear the motor is running, but not pumping water, check the pump impeller.
2c: If the water pump was run by the main motor same as the agitation, then check the pump engagement solenoid, this solenoid applies pressure from the main motor shift to the pump then it will move water.
Read the following"
The water pump recirculates water during the wash cycle and pumps it out for the spin cycle. Some washers use the recirculation to mix and distribute add-ins like bleach or fabric softener. In some models the spin cycle starts while the water is still in the tub; others drain first before the spin cycle starts.
A blocked or malfunctioning water pump can be responsible for many different washer problems; see our diagnostic page for the list. Note that while a problem may seem to be related to the pump, the problem may really lie in one of the connecting hoses. Each of the hoses that connects to the water pump should also be inspected. A blockage may occur anywhere in the water's pathway.
There are two types of pumps; direct drive and belt drive. The direct drive is mounted directly to the motor, the belt drive is mounted to the chassis. The direct drive style can be opened for complete inspection while belt drive models may or may not be designed to be opened. You can however, still remove the hoses and inspect the ports for a blockage. Inspecting the pump is fairly easy to do, but you will most likely have to open the washer's cabinet.
Typically one of three problems occur with the pump. The first is a blockage in the pump, often from small items like a sock. The second possibility is that the impeller blades become broken or worn down and cannot move water efficiently. Finally, in belt drive models, if the belt is loose or broken it does not turn the pump.
Locate the pump, it will have two, three or four hoses. Label each hose and where it connects. The hoses should each have a wire clamp or a hose clamp with a screw. Pinch the wire tabs together with pliers and wiggle the clamp farther up the hose. Screw style hose clamps are simply loosened by turning the screw, then slide the clamp up the hose. Now remove the hose from the port.
Direct drive pumps have metal clips that hold the cover plate unto the pump assembly. Use a screwdriver to pry up the clips and remove the cover. Pull off the pump's impeller unit and inspect for damage.
Belt drive pumps vary and may or may not be designed to open for repair. Examine the pump to determine whether it can be opened. If it cannot be opened the look into the ports for any blockage.更多精彩文章及讨论，请光临枫下论坛 rolia.net